Chaileapedia
Chaileapedia › Carrier & Fixed Oils
Carrier & Fixed Oils

Base Oils in Soap Guide: Fatty Acid Profile, Hardness, Lather and Care Comparison

In short: The base oils in a soap bar largely determine its hardness, its lather character and the skin-care feel it leaves behind, because the saponification reaction takes over the fatty acid profile of the oil as it is.
Base Oils in Soap: Fatty Acid Profile, Hardness, Lather and Care Comparison

Introduction — The base oil is the chemical backbone of soap

The behavior of a soap bar is largely determined the moment the oil blend is chosen, long before it is poured into a mold. In the cold-process method, the triglycerides in the oils combine with an alkali (NaOH or KOH) to form soap salts and glycerin. This reaction is called saponification, and the chemical properties of the resulting soap are inherited directly from the fatty acid composition of the oils used. "Base oils in soap" is therefore not a matter of hobby preference but the central decision point of formulation.

This guide is based on a table compiled while assembling monographs on 18 different raw materials at the Chailea workshop. The aim is to make each oil's saponification value (SAP) and dominant fatty acids readable at a glance, and then to explain in chemical terms how these numbers translate into hardness, lather and skin-care feel on the bar.

Fatty acid glossary: Six players and their roles

Six fatty acids stand out in the majority of vegetable oils and define soap behavior. Chain length (carbon count) and the number of double bonds largely define a fatty acid's role in soap. As molecular weight increases (PubChem compound data), the number of saponifiable ester bonds per gram of oil decreases; the amount of alkali needed per gram, i.e. the SAP value, therefore falls. On a molar basis, saponification is 1:1 for every fatty acid ester (one ester bond consumes one mole of alkali); the variation of SAP from oil to oil arises because the value is defined on a mass basis (mg alkali / g oil).

Beyond these six there is one exception: ricinoleic acid (C18:1-OH, 298.5 g/mol), the defining component of castor oil (Ricinus communis). Its hydroxyl group explains why castor oil, used in small amounts, considerably strengthens the lather by lowering the surface tension of the soap solution.

Master table: 18 base oils in one comparison

The values below are typical ranges. As emphasized in the Codex Alimentarius standard CXS 210-1999 (2015 revision), fatty acid percentages can vary across a wide band among varieties and origins of the same plant; the lye calculation of each formulation should therefore be made for the specific batch used. The NaOH-SAP values are given in the coefficient form used in calculators.

Oil INCI NaOH SAP Lauric % Myristic % Palmitic % Oleic % Linoleic % Contribution to the bar
Coconut Cocos Nucifera Oil 0,183 45–50 16–20 8–10 5–8 1–3 Hardness + large-bubbled lather
Palm kernel Elaeis Guineensis Kernel Oil 0,156 45–52 14–18 7–9 12–19 1–3 Hardness + fast lather
Palm Elaeis Guineensis Oil 0,141 0–1 ~1 40–46 37–42 9–11 Hardness + stable lather
Olive Olea Europaea Fruit Oil 0,134 – – 8–14 65–80 4–15 Soft, care-oriented
Sunflower Helianthus Annuus Seed Oil 0,134 – – 6–8 20–40 50–70 Silky care, short shelf life
Safflower Carthamus Tinctorius Seed Oil 0,136 – – 5–8 10–20 68–80 Silky care, turns rancid quickly
Canola Brassica Napus Seed Oil 0,132 – – 4–5 55–65 18–25 Conditioning, soft lather
Sesame Sesamum Indicum Seed Oil 0,133 – – 8–12 35–45 40–48 Balanced care
Sweet almond Prunus Amygdalus Dulcis Oil 0,136 – – 6–8 62–78 15–30 Gentle, creamy conditioning
Apricot kernel Prunus Armeniaca Kernel Oil 0,135 – – 4–8 55–70 20–35 Light-textured care
Hazelnut Corylus Avellana Seed Oil 0,135 – – 5–7 70–83 8–19 Care similar to olive, slightly lighter
Avocado Persea Gratissima Oil 0,133 – – 10–20 55–75 6–15 Conditioning + slight hardness
Cocoa butter Theobroma Cacao Seed Butter 0,137 – – 24–30 30–38 2–4 High hardness + creamy lather (stearic 30–36)
Shea butter Butyrospermum Parkii Butter 0,128 – – 4–8 40–55 3–8 Hardness + rich conditioning (stearic 35–45)
Castor oil Ricinus Communis Seed Oil 0,128 – – 1–2 3–4 4–5 Lather booster (ricinoleic 85–90)
Flaxseed Linum Usitatissimum Seed Oil 0,135 – – 5–7 18–22 14–18 Fine care; turns rancid quickly (linolenic 50–60)
Jojoba Simmondsia Chinensis Seed Oil 0,069 – – – – – Liquid wax ester; small-amount conditioning
Argan Argania Spinosa Kernel Oil 0,136 – – 12–15 42–48 30–38 Balanced conditioning, silky feel

The fatty acid percentages in this table rest on the compilation of vegetable oil composition measured by GC analysis by Orsavova et al. (2015), and on the study by Laureles et al. (2002) reporting the lauric acid range in Cocos nucifera hybrids (45–50%, and 50.45% in a single hybrid).

The chemistry of three properties: How hardness, lather and care arise

Hardness arises from saturated and relatively long-chain acids (lauric, myristic, palmitic, stearic) whose straight carbon backbones pack tightly among the soap salt crystals. This is why coconut, palm kernel, palm, cocoa butter and shea butter act as levers for a hard bar.

Lather is described in two distinct characters. Oils rich in lauric and myristic acid (coconut, palm kernel) give a fast-forming, large-bubbled and fluid lather. Hard fats rich in palmitic and stearic acid (cocoa, shea, palm) produce a small-bubbled, creamy and more stable lather. The sensory panel study by Prieto Vidal et al. (2018) on commercial natural soaps documents, at peer-reviewed level, the link between the proportion of saturated acids and lather density.

The care feel comes from unsaturated fatty acids and from glycerin, a by-product of saponification. Oleic acid leaves a sense of slipperiness and moisture on the skin even in soap-salt form. Linoleic and linolenic acids silkify the texture; however, as the number of double bonds rises, the oil's susceptibility to oxidation also increases. This is a balance point underlined by the same study: as the unsaturated share rises, shelf life shortens.

Bars dominated by olive oil, with their soft, strongly care-oriented character and measured hardness and lather, are the classic example of this three-part logic; for a detailed monograph, the article on the 5,000-year history of olive oil in soapmaking can be consulted. The contrasting behavior of coconut is examined in more detail in the Cocos nucifera monograph.

The chemist's decision framework: How a blend is built

From a chemist's perspective, soap formulation is the task of adjusting the proportions of three blocks: the hardness block, the lather block and the care block. Bars made from a single oil usually cannot meet all three axes at once. A high lauric content gives a hard, strongly lathering bar but may leave the skin feeling dry. A high oleic content gives a gentle bar, but it stays soft and produces less lather. For this reason, base oils are typically blended so that they complement one another.

A rough chemist's framework can be summarized as follows:

How the saponification reaction is controlled, and why each oil must be calculated with its own SAP coefficient, is explained step by step in the article on how cold-process soap differs from traditional soap.

Common mistake and its consequences

The most frequent error in new recipes is putting a single oil in the foreground. A bar built on sunflower or safflower alone, because its linoleic content is high, can turn rancid quickly and develop yellow surface spots (DOS). Bars built only on olive oil in the Castile style need a curing process lasting weeks before they harden. Bars built only on coconut are hard but may be too drying for a hand that is washed often. The ranges in the master table are the numerical explanation of why these three extremes balance out at a midpoint.

As a final reminder, the fact that the SAP value is a narrow band rather than a single number is a reality emphasized in official food standards such as Codex CXS 210-1999. For this reason, each new batch of oil is recalculated for each recipe using a mass-to-alkali ratio recorded in the lab notebook, and the superfat share is determined within this framework.

Frequently Asked Questions

Why does a soap recipe contain more than one base oil?

Hardness, lather and care properties are provided by different fatty acids. A single oil cannot balance all three axes at the same time; blending holds the three blocks together.

Why do SAP values look slightly different from one source to another?

The fatty acid composition of an oil varies with the plant variety, origin and harvest conditions. For this reason, official standards such as the Codex Alimentarius give SAP values as a range rather than a single number, and the lye calculation is also made with a safe superfat margin.

Why does a bar high in lauric acid sometimes feel dry on the skin?

The soap salt derived from lauric acid is relatively soluble in water and interacts more strongly with the lipid film on the skin's surface. This sensation is a matter of skin feel rather than a health issue by itself; it is normal to balance it by raising the share of oleic-rich oils in the blend.

Why is castor oil used in small amounts among the base oils?

The dominant component of Ricinus communis oil is ricinoleic acid. Its hydroxyl group markedly enlarges the lather; however, at high levels the bar can become soft and sticky in texture, which is why it is typically used at around 5–8%.

Sources


Read the original in Turkish on chailea.com →

Oğuz Kağan Dereci

MSc Chemist · Chailea / ChaiNovi Sanayi Ticaret Ltd. Şti.

Chaileapedia grows out of the ingredient research behind Chailea's cold-process soaps in Rize, on Türkiye's Black Sea coast. Each entry is documented by INCI name, with cited sources, and without overstatement.

Chaileapedia is an educational reference about cosmetic ingredients and the science of soapmaking. It is not intended to diagnose, treat, cure or prevent any disease.